Natural Start Bottle

Before first use, disassemble and place all components in boiling water for 5 minutes to ensure hygiene. Follow the below steps to ensure your bottle is safe and ready to use:

1. Disassemble your bottle
2. Wash all parts in warm soapy water and rinse or use a dishwasher (top shelf only).
3. Use a teat brush to gently clean the teat (C). Do not turn it inside out as this may cause damage. Do not clean the feeding hole or anti colic valve (D) with the brush as damage may occur.
4. Reassemble your teat (C) and screw ring (E) and then place all the parts in boiling water for 5 minutes or use another method of sterilisation such as microwave (see ‘How to self-sterilise’ tab), UV or steam sterilisation or cold water tablet/liquid solution.
5. After sterilising, reassemble your bottle ready to use.
6. To prevent the teat (C) from collapsing during feeding, pinch the valve (D) gently between your fingers to ensure it’s open.

This method allows you to easily sterilise bottles using a microwave. Before self-sterilising, always wash all components thoroughly and rinse in clear water or use a dishwasher (top shelf only).

1. Assemble the teat (C) in the screw ring (E) and click the bottle hood (A) in place.
2. Pour exactly 50ml of water into the bottle base (F). The bottles have a 50ml measure (G).
3. Rest the assembled hood (A), teat (C) and screw ring (E) on top of the bottle base (F). Do not tighten to the base.
4. Place in the microwave for 3 minutes. To sterilise multiple bottles see the timings table below. For glass bottles allow 30 minutes to cool down with the microwave open.
5. Pour out residual water and screw the assembled hood (A), teat (C) and screw ring (E) on to the bottle base (F) ready for use. After sterilisation the bottle and the teat will remain sterile for 24 hours if the bottle is unopened and fully assembled. Always store bottles fully assembled.
6. To prevent the teat (C) from collapsing during feeding, pinch the valve (D) gently between your fingers to ensure it’s open.

Microwave recommended times for all bottle sizes. Based on microwaves from 700 to 1000 Watts.

• Inspect before each use and pull feeding teat in all directions
• Always clean and sterilise before each use.
• Keep away from solvents or harsh chemicals.
• Do not allow the product to come into contact with oil based foods.
• Not suitable for use in a conventional oven or a combination microwave oven with the grill feature switched on.
• Do not leave the feeding teat in direct sunlight or heat or leave in disinfectant (“sterilising solution”) for longer than recommended, as this may weaken the teat.
• Teats are recommended to be replaced at least every 2 months for safety and hygiene reasons.
• Please dispose of this product and packaging responsibly.

1. Disassemble your bottle
2. Wash all parts in warm soapy water and rinse or use a dishwasher (top shelf only).
3. Use a teat brush to gently clean the teat (C). Do not turn it inside out as this may cause damage. Do not clean the feeding hole or anti colic valve (D) with the brush as damage may occur.
4. Reassemble your teat (C) and screw ring (E) and then place all the parts in boiling water for 5 minutes or use another method of sterilisation such as microwave (see below), UV or steam sterilisation or cold water tablet/liquid solution.
5. After sterilising, reassemble your bottle ready to use.
6. To prevent the teat (C) from collapsing during feeding, pinch the valve (D) gently between your fingers to ensure it’s open.

The valve will work wherever it’s positioned but the best place for the valve is at the top, near your baby's nose.

The simple answer is no, due to the different valves. Most of our products have interchangeable parts to make life as simple as possible. But the Natural Start Teats have a built-in air valve, and don’t work properly on our Advanced Anti-Colic bottles.

Yes. Our Natural Start and Advanced Anti-Colic bottles are made from polypropylene (PP) that can happily be recycled.

The small holes allow the steam to flow and reach the external surface of the teat and the internal surface of the hood.

PLEASE NOTE: It’s important that the silicone teat is not tightened on to base when self-sterilising in microwave to allow the steam to flow in.

The 50ml of water in the bottle will turn into steam when microwaved*. The steam reaches the temperature necessary to sterilise, killing virus and 99.9% of bacteria. The steam travels around the bottle and through the holes in the screw ring to reach the external surface of the teat and the internal surface of the hood.

*Based on microwaves from 700 to 1000 Watts.

PLEASE NOTE: It’s important that the silicone teat is not tightened on to base when self-sterilising in microwave to allow the steam to flow.